The status indicators on my Blink cameras recently started flashing red, and I deduced that this has got to do something with the batteries.
But even after swapping the old battery pack for a fresh set, the problem still persisted leading me to venture into newer paths for troubleshooting.
This got me to write up this article on how you can fix your Blink cameras flashing red even after you swapped out the batteries for a fresh pair.
If your Blink camera is flashing red with new batteries, it could mean that the camera is connecting to the internet after boot. The red lights can also appear when the camera detects motion. The meaning behind red light varies with the Blink model.
Why Does the Blink Camera Flash Red After Swapping Batteries?
A battery-low alert is what usually triggers the red lights to flash.
The red light flashes 5 to 6 times, indicating that there is no sufficient charge in the batteries to power the Blink cameras.
Do not use rechargeable batteries to power Blink cameras as they most likely won't be providing enough volts to power the device.
If you still face a red light flashing issue after swapping the batteries, then the Blink cameras are most likely to be indicating other errors.
Blink has programmed the red lights to flash for different scenarios depending on the Blink cam model.
Why Do the Blink XT2, XT, Outdoor, and Indoor Cameras Show a Red Light?
The Blink XT2, XT, Outdoor, and Indoor cam models are the ones that support batteries for operation.
Here are the instances where the Blink XT2, XT, Outdoor, and Indoor cameras flash red:
|Flash red every three seconds||The Blink camera is disconnected from the internet|
|Five long red flashes||During the initial boot of Blink camera, before connecting to the internet|
|Short red flashes every three seconds||Blink camera is searching for a WiFi connection|
|Red light flashes briefly||Happens during motion detection|
If you notice red flashes still after swapping the old batteries with a fresh pair, do not worry much as that is something the Blink cameras do initially.
Similar to the green light, the Blink cameras will still flash, typically five long flashes, and keeps repeating the flash till the device connects to the internet.
You might also notice red flashes if the Blink camera detects motion.
If the red lights still persist after the above-mentioned conditions are cleared, then it could just mean that the swapped batteries are not compatible.
Make sure that the two batteries are fresh 1.5A AA Lithium non-rechargeable batteries.
A Red Light Status on Blink Video Doorbell Cameras
The indications for Blink Video Doorbell cameras reside on the LED ring surrounding the doorbell button.
It is usually triggered when the camera is connecting to your home network.
It also shows up during the initial setup or when it detects a change in your WiFi connection, indicating that the Doorbell is ready to connect.
In such cases it is best to make sure that the following steps are valid:
Check Your Internet Connection
Make sure that your internet connection is up and running properly.
The best way to check the status of your internet connection is to try connecting your smartphone or laptop to the network.
If data transfer is occurring as expected, then you are good to go.
Check Your Internet Router
If your internet connection is not working as expected, then do check your internet router's indication lights to decode the situation.
If your router is showing any error signals, then it is best to first get that patched up.
Why Does the Blink Mini Camera Show a Red Light?
If your Blink Mini is showing a red light, it is sending you a message that it has no connectivity to the internet.
This can happen with issues with your home network, which you can try to patch up by following the internet connectivity and router checks mentioned above.
If the red light still persists after a proper internet connection, then you can follow the troubleshooting steps given below:
Power Cycle Your Blink Camera
A power cycle is simply a hardware reboot for your Blink camera.
This basically resets all the charges that reside within your Blink camera and basically refreshes the device from within.
It helps in getting rid of any unbalanced charges that might have been residing within your system that might have been wreaking havoc.
You can perform a power cycle on your Blink cameras, no matter which model, by following the steps given below:
- Unplug your Blink camera from power. If your camera uses batteries, then remove the batteries.
- Let the Blink camera sit idle in its powered-off state for about a minute.
- Plug the Blink camera back to power. If your camera uses aged batteries, swap them out for a fresh pair.
- Let the Blink camera sit idle in its powered-on state for about a minute.
Try connecting the Blink camera to your WiFi again after performing the power cycle to check if the red light still hasn't changed to a solid blue.
Reset Your Blink Camera
If the above steps do not help in getting rid of the red light situation, you can proceed to perform a factory reset on your Blink camera.
This will wipe out all data from the Blink camera and will completely recover the Blink camera to factory defaults.
Do note that Factory resetting will remove all connected devices, and you will need to pair the device again using the Blink app on your smartphone or tablet.
You can perform a factory reset on your Blink camera by following the steps given below:
- Using a smartphone sim ejector pin, thumb tack, or any similar small and sharp object, press the reset button hole on the underside of your Blink camera.
- Keep pressing till the red light changes to a blue and green light, signifying the initiation of the reset process.
Do not insert the sharp pin too deep into the reset hole on your Blink camera, as that can potentially cause hardware faults.
If you still face issues with your Blink camera randomly flashing red without much luck fixing it, you can try contacting Blink support.
I hope my article on how you can fix your Blink camera flashing red has been a worthwhile read and has aided you with the same.
Have a good day!
Frequently Asked Questions (FAQ)
How much life does a fresh set of batteries provide for Blink XT2?
The Blink XT2 can record up to a total of 53,870 seconds (about 15 hours) on a single pair of 1.5V batteries, leading to a 2-year endurance.
Is Blink owned by Amazon?
Blink Cameras are a smart security camera division that is owned by Amazon.
You May Also Enjoy Reading
- Blink Camera Clicking Sound: How To Fix 
- Blink Camera Speaker Not Working: How to Fix 
- Blink Camera Not Recording At Night: How To Fix 
- Blink Cameras Failed To Arm: How To Fix 
- Blink Camera Only Recording 1 Sec/5 Sec/20 Sec: How to Fix 
- Blink Camera Thumbnail Failed: How to Fix 
The comments are closed.